tekno

Selling my VERY lightly used Tekno MT410. When I was younger I always wanted a hobby grade R/C. During Covid boredom I did a ton of research and built up this MT410. I loved the process, but with two small children I just never had time to use this. I literally ran it in my cul-de-sac a couple...

I am in the process of completing my ET48 2.0 Thread. This is my first kit build since a Nikko Dandy Dash ~1988. So, it has been a while. Handed down my Slash Ultimate 4x4 to my daughter and tried to buy a Teckno ET48.3 last March but as everyone knows they were discontinued until the ET48 2.0...

New Tekno RC ET48 2.0 1/8th 4WD Competition Electric Truggy Kit![/HEADING] At the Tekno RC HQ, one of our favorite classes is E-Truggy. Plenty of power, large truck tires, and loads of fun with friends. We brought E-Truggy to the masses with the original ET48 and refined it to be one of the...

Hey guys I'm new to the hobby and I am not 100% sure what tires will fit properly and which won't. Would these tires fit by any chance? If they do not fit please direct me to some that will. I'm looking for a nice tready tire...

Hey guys, hope all of you are staying safe and ripping some hot laps :) I've looked over the manual a few times, and watched a few unboxing vids. But for the life of me.. I can't find an answer to my question, I'm hoping someone here can help. Does the ET410.2 come with a receiver box? If...

I just got my SCT410.3 kit from FedEx, and my M2C wide truggy chassis and braces arrived a couple of days ago... So here is the starting point of my Desert Buggy build. I'm using a Castle Creations 1515/2200 Kv motor and Mamba Monster X ESC combo, and a Reefs 777 steering servo. I also have a...

Hello everyone, After multiple setup test, i ended with: (all stock, just a little piece of m2c racing on the rear tower) motor Supass Hobby taurus 4274 1500kv (88amp, max 32v/2800w) Tekno 16 tooth pinion, stock plastic 44 spur (have the metal 44 and 46) ESC Hobbywing max8 150amp (punch 3/5...

Finally have the MT kit and enough of the bits to get this beast built. Might be a bit sporadic of a build, as my free time is limited, but will make a strong push to not drag it out and to stay up on postings. Here is the BOM: MOTOR: Castle 1515 2,200KV sensored brushless motor. Out of stock...

Went with a Novak 550 4 pole 3900, 150a Skyrc TS pro 1:8 scale esc. I had to put the receiver to the rear and use a spare bolt hole for the antenna. Fun build!

Hey everyone. Thought I’d share a few snaps of my M2C game changer chassis build. Great quality and everything went together well. Running a Max 8 2200kv but previously ran my Tekin 1900kv which might go back in yet. Drives like a little tank and seems to handle hits like one too. I built this...

Does anyone run a servo saver on an EB410? If so which one would you recommend?

Hey everyone, im just joining the world of rc cars and so far its not gone too well. I just picked up a used SCT 410.3 off of my local buy and sell conplete RTR. I tested it out in the parking lot before purchasing but never pinned it. Just took it out to the my farm to give it a test, made it...

I’ve been slowly building an MT410 and have been loving the build. It’s really been helpful having all of the knowledge and information about these cars here. I’ve been reading and searching even before I bought my kit and it’s taught me a lot. I’m glad this site is available and everyone is so...

Looking for the right one to give a good home to... ?

Keeping the first post open for up to date picture and equipment list Kit arrived!!

Hello to everyone and thank you in advance for your help. I haven’t driven my MT410 in about six months, not my choice life just got busy. I do not know what you guys would suggest that I do before starting to drive it again. Thanks once again

I remember when I first started reading RC forums; there had been, for years, thoughts of modifying a stadium truck into a 4wd "animal". Time past, and OFNA did it. They (OFNA/HoBao) put out the Hyper 10-TT. I thought that was just plain 4wd stadium truck greatness! I couldn't see myself coming...

Thinking about buying my first tekno what all upgrades does the mt need before bashing and is it worth every cent? how's durability on it? Also what are the most common issues with it? Give me all the info I need to know thanks guys

Was very good build I enjoyed it. Still have stuff to do but almost complete I also painted with my new air brush for the first time as well. The body is all paint no decals but I went to far with my blade cutting out the liquid mask oh well its a bash body!! Will gorilla tape in the body. Jason...

New to the et48 and trying to get a slightly larger steel spur gear. Can anyone tell me that highest tooth count that will fit? I am running pretty large tires and I am not able to gear down as much as I’d like. I figure making the spur a little bigger will help. The motor mount doesn’t slide...