• Welcome to Tekno RC Forums! Are you a Tekno RC fan? If so you're in luck as you've have arrived to the biggest and best Tekno RC community.

    Come join our community and ask your questions, show off your Tekno RCs and share your experience!

esc

  1. M

    Hobbywing EzRun XR8 sct problems

    Hey everyone, im just joining the world of rc cars and so far its not gone too well. I just picked up a used SCT 410.3 off of my local buy and sell conplete RTR. I tested it out in the parking lot before purchasing but never pinned it. Just took it out to the my farm to give it a test, made it...
  2. Relic01

    Are people putting 6s LiPo in the Tekno MT410?

    Am I reading this right ? People are putting 6s lipo set ups in the tekno mt410? Is this the TEKIN 200kv motor and the rx8 gen 2 set up? I've got my kit on the way, just trying to clear up where I want to be with this project when compleated, any suggestions are very appreciated.
  3. P

    Waterproof motor & ESC for ET48.3

    Hi All. I'm a newbie and I've got my new ET48.3 up and running and love it! I used the old electronics (MXL-6s and 2200kV motor) from my ERevo Brushless Gen1 and I'm using a 15T pinion. I run 90% of the time in the backyard grass on a course that we setup. So the vehicle is running hard...
  4. S

    Hello, new to forum with motor esc question MT410

    Hello everyone. I have been running 6s ARRMA vehicles and this is my first kit, MT410. The quality of this kit is just amazing and a blast putting together. After reading lots of threads and research I am still trying to figure out if I want to run 4s or 6s. I run 6s on my ARRMAs but don't...
  5. S

    HW Max 8 install for MT410

    I am currently attempting to install the HW Max 8 ESC on my MT410. I noticed it does not fit smoothly up against the steering servo which results in the mounting holes not aligning correctly with the mounting plate. I feel like I read a while back I would be encountering this issue. My questions...
  6. ZUMA

    Just pulled the trigger on an MT410

    Been looking at an MT410 for some time and today I bought one. Right now, I'm reading through the threads looking for ideas on my build. Any tips and tricks would be great. Right now, I'm currently running an E-Revo on 6S and loving the speed and power on 6S but ya it tends to break (I bet a lot...
  7. B

    Hobbywing ESC and 3660

    Got the Tekno SCT410 put together and when I initially pull the throttle it continues for a couple seconds. How do i fix this?
  8. Fergusonv

    6S and Tekin 1350 - looking for feedback

    Looking for advice. I want to run 6S and Tekin. I've got my kit ordered and was about to place an order for esc and motor but thought it best to get feedback here first. It appears to me that the best 6S rated motor offered by Tekin is the 1350 Truggy motor. I was thinking 17/44 gearing (steel...
  9. V

    Mt410 esc and motor?

    So I'm building my MT410 now but still need an ESC and motor. I live in Ohio so I have snow and will run it in the winter waterproof is a must im looking at the mamba monster. I'm new to electric and don't know if i was want the 1700kv or 2200 speed and standing backflips not needed don't want...
  10. WoodiE

    Recommended Tekno ET410 Equipment

    This is a list of Tekno RC suggested equipment list for the new Tekno ET410 1/10th scale truggy. This is just some initial recommendations so please share below what gear you are or plan on running in your Tekno ET410 truggy. Front & Rear Wheels - 12mm hex, AE offset Associated stadium truck...
  11. Slogrits

    MMX on off switch.

    Trying to wrap up the few problems with my build. How do you make the castle on/off switch stay in place. I tried double stick and Velcro.
  12. thirtydaZe

    Motor Fan Quits Running

    Bare with me as i've asked about this on FB and at rctech. Here is my Original post, Some of you may have seen it. Having a bit of a technical issue. I was at practice the other day, coming off of a jump and entering the straight. My cars wheels went full right, and then lost all power. Pulled...
  13. cordell12

    48.3 et48.3 Help me choose a motor and esc

    Hello everyone Bought me a et48.3 roller this morning (no pics yet, being shipped) and was curious on what you guys think about motors. I currently have a choice of 2 different motors, a Castle 1515 2200kv and a Leopard 4092 1480kv. I am leaning towards the Leopard, but know that the Castle can...
  14. S

    Castle mamba monster w/ 2200kv. 4s or 6s?

    Hey guys quick question. Got my hands on a castle mamba monster and 2200kv motor. It says they are 6s capable but who actually runs theirs constantly on 6s? Is 2200 and 4s 50c suffice for a fun basher? Don't wanna be overheating every 10 min. Any Input? Thanks
  15. Illestep3

    What motor/ESC combo do you recommend?

    What are you guys running for motor/esc combos ? And what do you guys like most about the current setups ?
Back
Top